Long Stroke Hydraulic Pumping Unit

The FRN wireline-retrievable flapper valve, which is normally closed, is held open by hydraulic control pressure from the surface. The valve operates on a hydraulic-piston principle. To open, tubing pressure slightly higher than the well pressure below the closed flapper is applied. Once well pressure is equalized across the closed flapper, hydraulic pressure is applied to the piston, which pushes the flapper open. The flapper hinge assembly is designed so the force on the piston is not applied directly on the hinge pin. Upon loss of hydraulic pressure in the control line, the valve's large spring serves to lift the hydrostatic head of the control fluid. The flapper spring is designed to close the valve when the piston moves up past the flapper. Opening Prong Nose Seal The FRN valve uses the valve housing as the downstop for the opening prong. This metal-to-metal (MTM) interface is designed to prevent flow from passing between the valve housing and opening prong. The MTM interface isolates the flapper and seat from fluid flow while the valve is open. This design creates an MTM interface with the full force exerted by the hydraulic piston, minus the spring compression force, holding the two metal faces in contact. Radius of Curvature at Flow Entrance Halliburton conducted a study with various curvatures on the entrance to the valve. The study tested abrasive fluids flowing through different test subs and examined the resulting wear patterns. As a result, an optimum radius of curvature was determined and implemented on the valve housings of all wireline retrievable safety valves. Applications » New completions » Deep set » High pressure Features » High-strength rod-piston actuation » Non-equalizing flapper closure » Solid construction flapper made from bar stock » Spherical radius seat on flapper improves seal reliability » Sealing and seating surfaces are out of flow path of well production when valve is in open position » Designed for easy field servicing *information referenced from supplier catalog.

Transforming Efficiency: Elevate Your Operations with ELEKS Experience a new level of operational efficiency with ELEKS' custom software development and data science services. Our cutting-edge solutions empower utility companies to embrace intelligent automation, optimizing complex processes and workflows across logistics, inventory management, warehousing, production planning, billing, and consumer management. With ELEKS as your partner, you can streamline your operations, achieve peak efficiency, and realize substantial cost savings. Empower Your Operations with ELEKS Energy Software Development: Embrace an advanced energy management software solution that revolutionizes productivity, accessibility, safety, and sustainability within your business power system. Intelligent Automation Expertise: Our custom software development and data science services enable you to adopt intelligent automation for critical processes. Say goodbye to repetitive, labor-intensive tasks and hello to efficiency and accuracy. Real-Time Insights: Gain real-time data on your operational conditions. Our solutions provide you with up-to-the-minute insights that help you make informed decisions and stay ahead of challenges. Minimize Errors and Costs: Automation minimizes human errors, reducing the risk of costly mistakes in critical processes. Achieve cost savings by optimizing workflows and minimizing resource wastage. Why Choose ELEKS? Proven Excellence: ELEKS boasts a 30-year legacy of excellence in custom software development. Our solutions are tried, tested, and trusted by energy producers, distributors, and governmental organizations. Cutting-Edge Innovation: Stay ahead of the curve with our utilization of cutting-edge technologies, including Cloud, IoT, blockchain, and data-driven solutions. Our software development team is equipped to address the evolving needs of the energy and utility industry. Tailored to Your Needs: Our solutions are tailored to your specific requirements, ensuring that you receive a technology platform that seamlessly integrates into your existing workflows. Revolutionize Your Operations: Join the ranks of industry leaders who are revolutionizing their operations through intelligent automation. With ELEKS as your partner, you can optimize processes, enhance accuracy, and unlock significant cost savings. Lead the Change with ELEKS ELEKS' custom software development and data science services empower utility companies to take charge of their operations, embracing automation for lasting efficiency gains. Say goodbye to manual, error-prone processes and hello to streamlined workflows and real-time insights. Take your operations to the next level – choose ELEKS as your partner in transformation.

The Premier™ packer is a hydraulic-set, large-bore, removable production packer. It combines the performance of a permanent packer with the conveniences of a retrievable packer. The Premier is ideally suited for big-bore completions and multizone stacked-packer completions. Its retrieving options offer new alternatives in high intervention cost applications. We can source from current stock or direct from the manufacturer.

Introducing the SJP Sand Jet Perforator from Marlin Oil Tools: A Revolutionary Approach to Well Intervention and Perforation Marlin Oil Tools proudly presents the SJP Sand Jet Perforator, an advanced downhole tool designed to redefine the standards of well intervention and casing or tubing perforation. Tailored to integrate seamlessly with the Bottom Hole Assembly (BHA), the SJP Sand Jet Perforator utilizes a high-velocity gel-sand mixture to execute precise, abrasive cuts through well casing, cement, and even rock formations, ensuring optimal wellbore connectivity and performance. Key Features of the SJP Sand Jet Perforator: High-Precision Perforation: The SJP employs a gel-sand jet emitted at high speeds from durable, abrasive-resistant nozzles, targeting the inner walls of the casing for efficient perforation. Versatile Operation Modes: Designed with flexibility in mind, the SJP Sand Jet Perforator can operate in a basic continuous circulation mode or a ball-activated mode, offering adaptability to various operational needs. Durable Nozzle Construction: Crafted from materials resistant to abrasion, the perforator's nozzles withstand the harsh conditions of downhole operations, ensuring longevity and reliability. Enhanced Operational Efficiency: Whether performing casing perforation or preparing wells for further intervention, the SJP streamlines operations, reducing downtime and enhancing productivity. Seamless BHA Integration: The SJP Perforator is engineered to work cohesively with other BHA components, facilitating a comprehensive approach to well intervention tasks. Operational Flexibility: The ball-activated mode allows for pressure testing of the BHA or the use of additional tools below the perforator, expanding the tool's application range. Maximize your well intervention success with the SJP Sand Jet Perforator from Marlin Oil Tools, a leading-edge solution designed for unparalleled precision in casing and tubing perforation. Leveraging a high-speed gel-sand mixture for abrasive cuts, the SJP enhances wellbore access and productivity. With its robust, abrasive-resistant nozzles and dual operational modes, this downhole tool is optimized for a wide range of well conditions, ensuring durability and adaptability. Ideal for both continuous circulation and precise operations, the SJP Sand Jet Perforator is your go-to tool for efficient, reliable well intervention. Why Choose the SJP Sand Jet Perforator from Marlin Oil Tools? Precision and Efficiency: Achieve targeted, efficient perforation for improved well performance. Adaptability to Well Conditions: Tailor your operations with continuous or ball-activated circulation modes. Longevity in Harsh Environments: Count on durable, abrasive-resistant nozzles for sustained operation. Comprehensive Well Intervention: Integrate seamlessly with BHA components for a holistic intervention strategy. The SJP Sand Jet Perforator by Marlin Oil Tools represents the cutting edge in downhole perforation technology, offering oil and gas operators a powerful tool for enhancing well intervention outcomes. Incorporate the SJP into your operations to achieve superior precision, efficiency, and reliability in well perforation tasks.

The SP™ tubing-retrievable safety valve (TRSV) is a single rod-piston non-elastomer flapper valve designed for hostile environments and extended life applications where ultimate reliability is required. Potential leak paths within the valve are minimized with the single rod-piston design. The piston achieves a metal-to-metal (MTM) seal at its uppermost and lowermost positions to seal well pressure from the control system. The SP valves incorporate flappers using spherical radius sealing surfaces that help greatly improve seal reliability. The spherical radius design provides full MTM sealing integrity. For applications where either the OD or ID is restrained, SP valves incorporate a contoured flapper. OD/ID relationships are improved by the contoured flapper design, which helps provide superior MTM sealing when compared to other forms of curved flapper technology. Applications » For applications requiring ultimate reliability and longevity, such as high-temperature/high-pressure, and subsea completions, or hostile well environments Features » Non-elastomer dynamic piston seals » MTM static seal at upper and lower piston positions » MTM body joints » Flow tube fluted guide » 100% MTM flapper » Concentric thrust bearing » Wiper ring on upper flow tube » Cleanout ports in flow tube’s upper end » Internal exercise profile » Flow tube shock absorber » MTM face seat at flow tube downstop » Setting depths to 9,000 ft (2743 m) » Critical components isolated from well debris with valve in open position » Area above flow tube free of solids buildup » Flow tube can be manipulated by slickline » Protected from high flow rate slam closures *information referenced from supplier catalog.

SSG Consulting is a Project, Engineering and Construction Management Consulting firm, specializing in the implementation of Business and Project Management solutions on Mega projects in various industries. - Authorised KEY360 channel partner Our services cover the following: - Project Advisory & Audits - EMPCM Execution - Specialist Project Controls & Forensics - Project Digitalisation - Project Resourcing - Analytics & Dashboarding Our Track Record: - 25 BILLION MANAGED VALUE - 300 MILLION PLATFORM TRANSACTIONS - 80 DEDICATED STAFF - 10X BUSINESS PROCESSES IMPROVEMENT

Enhance Your Mining Operations with Wisdom's KL5MS Corded Miner's Cap Lamp from Provix Provix is proud to introduce the Wisdom KL5MS Corded Miner's Cap Lamp, a top-tier lighting solution engineered to meet the rigorous needs of the mining industry. Combining advanced technology with user-focused design, the KL5MS ensures both safety and efficiency for miners under the most challenging conditions. Powerful and Efficient Illumination The KL5MS boasts a high-capacity 7,800mAh battery, delivering a continuous discharging time of 13 hours. It features a main light LED with a working voltage of 3.0V, current of 640mA, and power of 1.92W. This efficient configuration provides a luminous flux of 340 lm, along with an impressive initial lighting degree of 18,000 lx at 1 meter, ensuring excellent visibility in dark mining environments. Durability and Longevity Designed for the long haul, the KL5MS has a main light life span of 50,000 hours and an auxiliary light life span of 40,000 hours. The battery's life span extends to 1,200 cycles under normal working conditions, underscoring the lamp's reliability and long-term performance. Safety as a Priority Safety is paramount in mining, and the KL5MS is crafted with this in mind. It is explosion-proof, adhering to ATEX GROUP II standards, and has an IP68 waterproof rating. Additionally, the lamp features a short circuit protection time of less than 320 μs, further enhancing its safety profile. Ergonomic Design for Comfort The KL5MS is designed with the comfort of the miner in mind. Weighing just 550g (19.40 oz) and with a main cable length of 1.65 meters (5.41 feet), it offers ease of use and mobility. The compact dimensions of the battery box (94 x 36 x 90 mm; 3.7 x 1.4 x 3.5 in) ensure that it is not cumbersome during extensive use. Quick and Convenient Charging With a charging time of just 4 to 7.5 hours, the KL5MS is ready for use quickly, reducing downtime and enhancing productivity. The USB charging feature adds an extra layer of convenience, allowing for easy charging in various settings. Get Yours Today Upgrade your mining gear with the Wisdom KL5MS Corded Miner's Cap Lamp for improved visibility, safety, and efficiency. Contact Provix for more information, visit our website at www.provix.net, or come see us in person. The Wisdom KL5MS is your key to safer, more efficient mining operations.

Enhance Your Automotive Services with Alignment Equipment Leasing from CWB National Leasing Streamlining Your Vehicle Maintenance with Flexible and Efficient Equipment Solutions For automotive repair shops, dealerships, or service centers, having reliable and precise alignment equipment is crucial for providing top-notch vehicle maintenance services. Leasing alignment equipment through Canadian Western Bank (CWB) National Leasing offers a flexible, cost-effective, and practical solution for businesses looking to enhance their service capabilities. Here’s how leasing alignment equipment can benefit your automotive business: 1. Quick Access to State-of-the-Art Equipment CWB National Leasing understands the importance of having the right tools for automotive services. They offer a rapid leasing process, typically making decisions within 48 hours of application submission. This efficiency means your alignment equipment can be delivered and operational quickly, minimizing downtime and enhancing your service offerings. 2. Increased Financial Flexibility Leasing alignment equipment with CWB National Leasing boosts your financial power. It allows you to conserve capital by opting for periodic payments over a significant initial purchase, freeing up resources for other essential business operations. The flexibility to add extra features or accessories to your equipment for a small payment increase enables customization to meet specific service needs. 3. Effective Cash Flow Management Manageable lease payments over the term allow your alignment equipment to start contributing to your business’s revenue while it's being paid off. This strategy helps maintain a balanced expense-to-revenue ratio, essential for business growth and financial stability. 4. Customizable Payment Plans CWB National Leasing offers a range of payment options, including seasonal, semi-annual, or annual plans, tailored to your business’s revenue cycle. This flexibility is particularly beneficial for businesses with variable or seasonal income, ensuring that payments are practical and aligned with your financial capacity. 5. Potential Tax Benefits Leasing alignment equipment can offer tax advantages, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is recommended to understand how leasing can positively impact your business’s tax position. Conclusion Opting to lease alignment equipment through CWB National Leasing is a strategic decision that equips your automotive business with essential service tools while maintaining financial flexibility. It ensures access to advanced alignment equipment, vital for providing high-quality vehicle maintenance services, without the financial strain of a large upfront investment. This leasing approach enables enhanced service efficiency, improved customer satisfaction, and increased profitability, helping your automotive business to thrive in a competitive market.

Optimizing Reservoir Connectivity with InWaTec Combined's Precision Perforating Services In the intricate execution of oil and gas production, establishing a seamless flow path between the reservoir and the wellbore is vital for optimal extraction. At InWaTec Combined, we specialize in precision Perforating Services, a critical step towards ensuring that our clients’ wells are prolific producers. Perforating is a sophisticated process, and its execution is both an art and a science. It involves the precise creation of holes from the wellbore through the casing and cement sheath directly into the producing zone. This process is not merely about making openings; it's about strategically placing them to maximize flow rates and enhance the recovery of hydrocarbons. Our approach to perforating is methodical and tailored. We begin with an in-depth analysis of the well conditions and reservoir characteristics. This data informs our selection of perforating techniques, which range from the conventional to the cutting-edge, including shaped charges and advanced explosive materials that create clean, deep perforations with minimal damage to the formation. InWaTec Combined’s Perforating Services are about more than just punching holes; they are about delivering a highly controlled and effective conduit for hydrocarbons to travel from the reservoir to the surface. With our state-of-the-art technology and expertly engineered charges, we can ensure that the flow path is not just established, but optimized for the specific conditions of each well. Safety and precision are at the heart of our operations. We employ the latest in downhole technology, including real-time monitoring and electric line conveyance, to ensure that our perforations are executed with the highest degree of accuracy and control. This commitment to excellence and attention to detail is why InWaTec Combined is a leader in the field. By entrusting InWaTec Combined with your perforating needs, you are not just choosing a service provider—you are choosing a partner dedicated to enhancing the productivity of your wells. Our Perforating Services are integral to preparing your wellbore to be a strong link between the hidden riches of the reservoir and the energy needs of the world. Let us bring our expertise and precision to bear on your operations, and together, we can unlock the full potential of your assets.

Precision Depth Control with InWaTec Combined's Casing Collar Locator Services Precise depth measurement is the linchpin of successful well completion and intervention. At InWaTec Combined, we recognize the pivotal role of accurate depth correlation in the lifecycle of a well, which is why we offer our specialized Casing Collar Locator (CCL) Services. These services are not just about measurement; they are about enhancing the precision of every operation that follows. The CCL is an essential tool in our suite of downhole diagnostic services, used to establish an accurate depth correlation between the casing collars and the open hole log of the well. This correlation is vital for a multitude of subsequent operations, particularly for the strategic placement of perforations and the depth assurance of wireline services within the cased hole. Typically run in tandem with a gamma ray, Cement Bond Log (CBL), or other cased-hole logging tools, our CCL services ensure that completion depths chosen from open hole logs are accurately transferred to the cased well environment. This step is critical because it anchors the location of future operations to a verified depth reference, ensuring that all interventions are performed at the intended stratigraphic intervals. The CCL log becomes a key depth control measurement, serving as a guide for precision perforating. It allows us to target the exact depth for the perforation guns, ensuring that we connect the wellbore to the hydrocarbon-bearing zones with pinpoint accuracy. This service is particularly crucial in complex wells where even small deviations can lead to significant complications. At InWaTec Combined, we understand that the integrity and success of cased-hole wireline services hinge on the reliability of depth measurements. Our CCL services provide a foundation of certainty upon which all subsequent interventions can confidently build. With our CCL technology, clients can expect a seamless transition from logging to completion, perforating, and beyond. Opting for InWaTec Combined's CCL Services means choosing a partner committed to precision and reliability. Our advanced tools, combined with our expert analysis, provide the clarity and assurance needed to execute well interventions with confidence. Ensure your operations are grounded in accuracy with InWaTec Combined, where every millimeter counts towards the success of your well.

The FXE wireline-retrievable flapper valve, which is normally closed, is held open by hydraulic control pressure from the surface. The valve operates on a hydraulic piston principle. To open, hydraulic pressure slightly higher than the well pressure is applied to move the piston downward. This pressure unseats the secondary seat, allowing pressure to enter through equalizing ports. Then, as additional hydraulic pressure is applied to the piston, it continues downward movement, pushing the flapper open. The flapper hinge assembly is designed such that the force on the piston is not applied directly on the hinge pin. Upon loss of hydraulic pressure in the control line, the valve’s large spring serves to lift the hydrostatic head of the control fluid. The flapper spring is designed to close the valve when the piston moves up past the flapper. Opening Prong Nose Seal The FXE valve uses the valve housing as the downstop for the opening prong. This metal-to-metal (MTM) interface is designed to prevent flow from passing between the valve housing and the opening prong. The MTM interface isolates the flapper and seat from fluid flow while the valve is open. This design creates an MTM interface with the full force exerted by the hydraulic piston, minus the spring compression force, holding the two metal faces in contact. Radius of Curvature at Flow Entrance Halliburton conducted a study with various curvatures on the entrance to the valve. The study tested abrasive fluids flowing through different test subs and examined the resulting wear patterns. As a result, an optimum radius of curvature was determined and implemented on the valve housings of all wireline-retrievable safety valves. Applications » General production completions Features » Equalizing-type flapper closure » Solid construction flapper made from bar stock » Spherical radius seat on flapper improves seal reliability » Sealing and seating surfaces are out of the well production flow path when valve is in the open position *information referenced from supplier catalog.

The C-1™ packer can be run as a conventionally set packer or, when run upside down, it can be set in compression. Emergency releases are provided for tension and compression operations. The G™ packer is an economical, compression-set packer, intended for lower pressure production applications. It is set by one-quarter-turn right-hand rotation. Release is accomplished by straight pickup of the tubing. If it is necessary to move the packer further downhole after release, one-fourth-turn left-hand rotation will put the tool back into the running position.

At Houston Digital Instruments (HDI Gauges), we prioritize providing our customers with cost-effective solutions that maximize the lifespan and performance of our products. We understand the importance of minimizing downtime and inventory costs while ensuring optimal functionality. That's why we offer a range of options for maintenance and repair, including spare parts, batteries, and repair kits. Additionally, our certified repair and calibration services guarantee the highest level of quality and precision. Let's explore how HDI Batteries, Parts, and Repair Kits can enhance your operational efficiency. Field Repairability: Minimize Lifecycle Costs HDI products are designed with field repairability in mind, significantly reducing the lifecycle costs associated with using our instruments. We believe in empowering our customers to perform maintenance and repairs on their own, enabling them to minimize downtime and spare unit inventory costs. Our DIY maintenance options are user-friendly and straightforward, ensuring that you can quickly resolve issues and keep your operations running smoothly. Spare Parts and Batteries: Keep Your Instruments Performing Optimally To support your maintenance efforts, HDI offers a comprehensive range of spare parts and batteries for our products. Whether you need replacement components, sensors, connectors, or other essential parts, our inventory has you covered. By utilizing genuine HDI spare parts, you can maintain the integrity and performance of your instruments, ensuring accurate and reliable measurements in the field. Furthermore, HDI batteries are specifically designed to deliver long-lasting power and reliability. We understand the critical nature of uninterrupted operation, and our batteries are engineered to provide optimal performance, even in demanding environments. With HDI batteries, you can trust that your instruments will continue to perform at their best, enhancing your productivity and efficiency. Repair Kits: Convenient Solutions for Maintenance and Repairs HDI Repair Kits are carefully curated packages that include all the necessary components and tools to perform maintenance and repairs on your HDI instruments. These kits are designed to simplify the process, providing you with a convenient solution to address common issues quickly. With HDI Repair Kits, you can efficiently resolve minor problems, minimize downtime, and restore your instruments to peak performance. Certified Repair and Calibration: Uncompromising Quality and Precision For more complex repairs or calibration needs, HDI offers certified repair and calibration services. If you prefer to have our expert technicians handle the maintenance and calibration of your instruments, simply ship them back to HDI. Our skilled professionals will carefully assess, repair, and calibrate your instruments, ensuring they meet our stringent quality standards. With HDI certified repair and calibration, you can have complete confidence in the accuracy and reliability of your instruments. HDI Batteries, Parts, and Repair Kits provide you with comprehensive solutions to enhance the lifespan and performance of your HDI instruments. Our commitment to field repairability allows you to minimize lifecycle costs, reduce downtime, and optimize inventory management. By utilizing genuine HDI spare parts, reliable batteries, and convenient repair kits, you can keep your instruments performing at their best. Additionally, our certified repair and calibration services ensure uncompromising quality and precision. Trust HDI Gauges for all your maintenance and repair needs, and experience the benefits of our cost-effective solutions. Contact HDI today to explore our range of batteries, parts, and repair kits tailored to meet your specific requirements.

Crew Transport buses for long term charter in locations around the world where reliable transportation is critical. Getting the crew to and from the job site in safety and comfort is key to a good start and end to the workday. Custom crew bus solutions available and every project is unique so please contact us to work together to find an optimum solution on crew transport.

Enhance Your Manufacturing Precision with Lathe Leasing from CWB National Leasing Transforming Your Production with Flexible and Advanced Equipment Solutions In the manufacturing and metalworking industries, lathes are essential for precision shaping and machining of various materials. Leasing lathes through Canadian Western Bank (CWB) National Leasing provides a strategic and financially sensible solution for businesses looking to upgrade or expand their production capabilities. Here’s how leasing lathes can benefit your manufacturing operations: 1. Rapid Equipment Procurement CWB National Leasing understands the need for timely equipment acquisition in fast-paced manufacturing environments. They offer a swift leasing process, with decisions typically made within 48 hours of application submission. This quick turnaround means your lathes can be delivered and operational promptly, minimizing disruption and enhancing your production line efficiency. 2. Increased Financial Leverage Leasing lathes with CWB National Leasing empowers your business with enhanced buying power. Opting for periodic payments over a hefty initial purchase frees up capital for other vital business needs. Additionally, the flexibility to add extra features or accessories to your lathes for a small payment increase allows for customization to meet your specific production requirements. 3. Effective Cash Flow Management Smaller lease payments over the term mean your lathes start contributing to your business’s revenue while they're still being paid off. This approach is essential in maintaining a balanced expense-to-revenue ratio, crucial for the financial health and growth of your business. 4. Customizable Payment Plans CWB National Leasing offers various payment options, including seasonal, semi-annual, or annual plans, tailored to your business’s revenue cycle. This flexibility is particularly beneficial for businesses with fluctuating or seasonal income, ensuring that payments are manageable and fit your financial situation. 5. Potential Tax Benefits Leasing lathes can offer tax advantages, such as the ability to expense lease payments instead of capitalizing the cost of the equipment. Consulting with a tax advisor is recommended to explore how leasing can optimize your business’s tax position. Conclusion Opting to lease lathes through CWB National Leasing is a strategic decision that equips your manufacturing business with essential machinery while maintaining financial agility. It ensures access to advanced lathes, vital for precise and efficient production, without the financial burden of a large upfront investment. This leasing approach enables enhanced operational capabilities, increased production capacity, and greater profitability, helping your business to thrive in the competitive manufacturing sector.

Elevate Your Business Towards Sustainability: Unleash Growth and Green Opportunities with ELEKS Sustainability Consulting In a world where sustainability is no longer an option but a necessity, ELEKS Sustainability Consulting emerges as your guiding light towards net-zero carbon emissions and environmentally-conscious growth. With a holistic approach encompassing consulting, implementation, and scaling, we offer an all-encompassing solution to drive sustainability while propelling your business forward. Paving the Way to Sustainability Success: Facilitate Sustainability Initiatives: Whether you're working towards net-zero carbon strategies or seeking to reduce your carbon footprint, our sustainability consulting services provide expert guidance. Our seasoned industry experts specialize in automating and optimizing processes for CO2 emission reduction. We'll guide you through end-to-end sustainability activities and empower your in-house team with environmental expertise. Optimize Project Costs and Timelines: Our comprehensive green consulting service ensures a cost-effective sustainability strategy. With three decades of software development experience and a network of cross-industry experts, we'll ensure your sustainability project aligns with your goals, budget, and timelines. Ensure Compliance and Avoid Penalties: As global sustainability frameworks become more comprehensive, compliance is critical. Our consultants help you navigate the complex landscape, ensuring transparency across your value chain and meeting GHG reporting frameworks and climate change legislation. Make Informed Investment Decisions: Our sustainability experts conduct thorough market research, empowering you to prioritize sustainable solutions. With a high-level roadmap and comprehensive data, you'll be equipped to make strategic decisions that drive sustainability and growth. Drive Sales and Foster Customer Loyalty: Elevate your brand by placing sustainability at its core. Our consulting services, backed by software development and digital transformation expertise, create a customer experience that resonates. This approach expands your client base, boosts customer retention, and fosters loyalty. Expand into New Markets: With sustainability as a focal point, explore new opportunities and markets. We analyze your objectives, research extensively, and help design services that resonate with your target markets, adding tangible business value. Unlocking Sustainability Potential - What's Included: Advisory on GHG Management: Our sustainability platform empowers you with consultancy on GHG accounting, reduction, and removal. Achieve transparency, traceability, and efficiency on your journey to net-zero. Our ready-to-use IT solution for carbon management is customizable to your needs. Technology Market Research: Navigate existing sustainability solutions from a business and technology perspective. Identify solutions that seamlessly enhance your market offerings and operations. Sustainability-Led Opportunity Scoping: Uncover new business opportunities and revenue streams by aligning the latest technologies and market trends with your expertise. A Journey Guided by Expertise: Conducting Initial Research: We dive deep into comprehensive market research, surveys, and interviews with stakeholders to understand your organization's challenges, needs, and goals. Defining Opportunity Areas: Based on your priorities, we define focused opportunity areas that promise the best returns, ensuring optimal investment in green business goals. Developing Business Cases: We create high-level business cases considering desirability, feasibility, and viability. These cases serve as a foundation for your sustainability journey. Crafting Architecture Vision: Once business cases are approved, our software experts identify tech stacks and components that align with your requirements, ensuring efficient execution. Presenting Outcomes: Our consulting culminates in a detailed report, offering a holistic description of business opportunities, technology areas, prioritization, implementation roadmaps, and budget proposals for your sustainability strategy. Our Focus Areas: • GHG Emissions Accounting, Reduction, and Removal • Transparency and Traceability • Waste Management • Circular Economy • Energy Transition • Life Cycle Assessment (LCA) Why Choose ELEKS Sustainability Consulting? End-to-End Sustainability Consulting: With over 30 years of software development and domain expertise, ELEKS Sustainability Consulting provides a comprehensive solution for all your strategic sustainability needs. Science-Based Approach: Our partnerships with universities and research institutions ensure evidence-based results. We engage niche specialists for reliable, data-driven sustainability outcomes. Robust Technological Capabilities: We integrate consulting outcomes seamlessly into your ecosystem and offer white-label solutions, minimizing additional investment in internal projects. Elevate Sustainability with ELEKS: ELEKS Sustainability Consulting is more than a service; it's a transformative journey that merges sustainability with growth. Join us as we navigate towards a sustainable future, where your business thrives while fostering a healthier planet.

Optimize Your Charging Process with the CSA 12 Unit Non-Locking FAST Charger Rack from Provix Provix is pleased to offer the CSA 12 Unit Non-Locking FAST Charger Rack (Part # NWI-NWCR-12BC), a streamlined and efficient charging solution ideal for modern mining, construction, and industrial environments. This charger rack is designed to rapidly charge up to 12 units, making it perfect for smaller teams or spaces. Rapid Charging for Minimal Downtime The CSA 12 Unit FAST Charger Rack is engineered for speed and efficiency, charging WISE LITE2 units in just 4 hours and LAMP3A/4A models in 5 hours. This quick charging capability is crucial for operations where equipment needs to be ready and operational with minimal delay, ensuring continuous productivity. Compact and Space-Saving Design With its non-locking, single-sided design, the CSA charger rack is an ideal solution for operations with limited space. Its compact footprint allows for convenient placement in equipment rooms, workshops, or mobile units, maximizing the utility of available space without sacrificing charging capacity. Versatile and User-Friendly The CSA 12 Unit Charger Rack is not just efficient and space-saving; it’s also incredibly user-friendly. Its straightforward design allows for easy access to all charging ports, facilitating the efficient management of multiple devices. This accessibility is especially beneficial in fast-paced work environments where time is of the essence. Durable and Reliable Construction Constructed to withstand the tough conditions typical in mining and industrial settings, the CSA charger rack is both durable and reliable. Its robust build ensures long-term performance, representing a sound investment for operations focused on efficiency and reliability. Ideal for Various Operational Sizes Whether you are part of a smaller mining crew, a construction team, or managing a rental fleet, the CSA 12 Unit Non-Locking FAST Charger Rack is an excellent choice. It allows for effective management of multiple devices, making it versatile for different operational needs. Get Your Charger Rack Today Upgrade your equipment charging station with the Wisdom CSA 12 Unit Non-Locking FAST Charger Rack from Provix. Visit www.provix.net now to learn more about this efficient, space-saving charging solution and take a step towards optimizing your operation’s productivity.

The WI retrievable injection valve is a high-performance, high-flow rate injection valve. High throughput is achieved by a unique valve configuration that minimizes turbulent and potentially erosive flow. Operation is not dependent on a specific flow rate, pressure, or setting depth, thus negating the need for adjustment over time. The valve incorporates a metal-to-metal valve and seat energized by the combination of an integral spring and well pressure acting from below. The WI injection valve can be deployed on a wireline lock or through-tubing pack-off device, providing flexibility not available with alternative injection valve systems. As a result of the simple design with fewer parts, redress and repair costs are considerably lower than those for other injection valve systems. Applications The WI injection valve is primarily used in water injection applications as an alternative to conventional tubing or wireline-set safety valves. The valve is also commonly used as a retrofit solution in water injectors in which a tubing to annulus leak has occurred. The valve can be deployed below the leak point to eliminate uncontrolled annulus pressure increases when the injection stops. Features » Compatible with all known lock systems » Dedicated designs to suit Halliburton EB0 intervention packers » Enhanced internal flow profile » Simple design and construction » Flow-loop testing performed to establish pressure drop versus pump rate *information referenced from supplier catalog.

The FRN wireline-retrievable flapper valve, which is normally closed, is held open by hydraulic control pressure from the surface. The valve operates on a hydraulic-piston principle. To open, tubing pressure slightly higher than the well pressure below the closed flapper is applied. Once well pressure is equalized across the closed flapper, hydraulic pressure is applied to the piston, which pushes the flapper open. The flapper hinge assembly is designed so the force on the piston is not applied directly on the hinge pin. Upon loss of hydraulic pressure in the control line, the valve's large spring serves to lift the hydrostatic head of the control fluid. The flapper spring is designed to close the valve when the piston moves up past the flapper. Opening Prong Nose Seal The FRN valve uses the valve housing as the downstop for the opening prong. This metal-to-metal (MTM) interface is designed to prevent flow from passing between the valve housing and opening prong. The MTM interface isolates the flapper and seat from fluid flow while the valve is open. This design creates an MTM interface with the full force exerted by the hydraulic piston, minus the spring compression force, holding the two metal faces in contact. Radius of Curvature at Flow Entrance Halliburton conducted a study with various curvatures on the entrance to the valve. The study tested abrasive fluids flowing through different test subs and examined the resulting wear patterns. As a result, an optimum radius of curvature was determined and implemented on the valve housings of all wireline retrievable safety valves. Applications » New completions » Deep set » High pressure Features » High-strength rod-piston actuation » Non-equalizing flapper closure » Solid construction flapper made from bar stock » Spherical radius seat on flapper improves seal reliability » Sealing and seating surfaces are out of flow path of well production when valve is in open position » Designed for easy field servicing *information referenced from supplier catalog.

KEY360 Inc offers a single integrated Business Management Platform comprising Business Intelligence, Project Management, Big Data & Analytics, ERP, Behaviour and Strategy Modification. - Over 140 Business and Project Management Systems on one platform available - Unique and extremely effective workflow engine - Remarkable “BIG DATA” and bulk transaction capability - Integrated Real Time reporting and dashboarding - Multi-company platform allows all project users to integrate seamlessly KEY Differentiators: - KEY360 Provides an exceptional opportunity for your organisation to attract new clients and build long terms relationships. - KEY360 is a Microsoft Gold Partner and Approved Microsoft Co-Sell Partner and can be purchased directly from the below online marketplaces: - Microsoft AppSource: KEY360 Capital Management Projects - Azure Marketplace: KEY360 Capital Management Projects - KEY360 is reputedly the most comprehensive and versatile Capital Project Management, Business Digitalization & Business Optimization solution available.